#Repair rusty bumpr Patch
#Repair rusty bumpr free

If All Else Fails…a Last Resort Re-plating chrome Just be sure to tape off the affected area and avoid overspraying. Chrome paints should be used to only hide imperfections, not for completely re-coating. There are many chrome paints you can try, like Testers (CS) Chrome Silver that some have said work well also. Applying chrome paint is somewhat of an art form, so you may want to practice on a spoon or other metal surface before attempting to touch up a spot or two. With any paint that you use, be careful before applying a clear coat on top, since this may actually dull the finish. Spaz Stix is water-based, and meant for RC cars but works well for small chips. If you have a larger surface, you may want to try a product called Spaz Stix. It’s actually used for building model cars and writing, but some have said it does the best job at mimicking the natural reflective surface of chrome.Ĭhrome is pretty difficult to match perfectly, but this product may be the closest to natural chrome you can get. You can pick on up on Amazon in a couple of different sizes, and from what I’ve read is the best thing you can use for small nicks here and there. If you still have imperfections that you couldn’t conceal with option 1, you may want to try applying the Molotow Liquid Chrome Marker. Step 4: Wipe away with a soft cloth and buff to a shine.Step 3: Wait until the product is dry and forms a haze on the surface.Step Two: Shake well and apply a small amount with an applicator or soft cloth to the affected area.

#Repair rusty bumpr free

Step One: Make sure the surface is clean and free of debris before applying product.

I found this product by Turtle Wax on Amazon you can try made specifically for this application. Option 1: Try chrome polish with rust remover The process of painting over chrome is quite extensive since you will need to clean, degrease, apply primer, as well as a chrome spray product as mentioned in option 3.

It obviously won’t replace the chrome, but can remove rust and bring your bumper back to life if rust is your main concern. Concealing Small Chips in ChromeĪssuming you have a very small chip or two and not a large surface, prepping with a rust remover or polish may be the simplest and most effective way to restore the overall appearance.Įspecially if you have very minor rusting, it’s usually best to try a polish before trying any other advanced methods. Keep in mind that these are simply suggestions, and to proceed at your own risk when attempting any DIY repairs. The same process generally applied to other surfaces like rims as well.

In this blog, I’ll share 3 simple ways to cover (or repair) chipped chrome on your bumper. The good news is there are a few ways to conceal these unsightly imperfections without completely re-chroming or replacing your bumper. Gravel, small rocks, salt, and other debris make chrome pretty easy to rust and show signs of wear if not protected.

#Repair rusty bumpr Patch

I have begun to prefer it over MIG welding a patch panel, but it isn’t always quicker or more efficient.So you’ve dinged, scratched, or have some unsightly pitting or rusting occurring on your chrome bumper. Once the panel is satisfactory you can use the 36-40 grit to smooth any imperfections and work your way up to 80-120 grit on the DA sander. This should leave you with a finish that’s acceptable for primer or a light coat of body filler. This method should require little to no grinding and is much more controlled. From here you can use a body file or a sander with 36-40 grit to sand the panel and highlight any offensive high or low spots and work them into shape. Slowly as you weld and hammer the seam you will connect all of your short seam welds and have a fully welded panel. This also allows you to let the panel to cool a little in between each weld to avoid overheating the entire panel. I like to stop after each short weld bead and hammer the weld to relax the panel back to its natural shape. The nice thing about TIG welding is that the weld seam is softer than MIG welding and it can be easily planished or hammered on-dolly to flatten it out and stretch the seam back into shape. Any type of welding causes extreme heat that causes the weld seam to shrink and cause a low spot in your panel.